View Profile: Son - Gunboard's Forums
Tab Content
  • Son's Avatar
    03-21-2017, 04:30 AM
    Son replied to a thread Safety issues in The Lee-Enfield Forum
    The pieces concerned are the sear and the cocking piece. The sear is boomerang shaped and transfers the motion of pulling the trigger to releasing...
    29 replies | 404 view(s)
  • Son's Avatar
    03-20-2017, 07:57 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    Sshhh... HE hasn't looked at this thread for two days.... If he does give you a D C M, let me know.... whats good for the goose....
    36 replies | 1131 view(s)
  • Son's Avatar
    03-20-2017, 06:26 AM
    Son replied to a thread Safety issues in The Lee-Enfield Forum
    Hi Nuclear_Inc. I see you got some pretty ill informed advice on the Facebook page... Ronbo6 is on the money, the safety should pull the cocking...
    29 replies | 404 view(s)
  • Son's Avatar
    03-19-2017, 08:30 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    Just had a look at how things are developing over there, noting the crickets and tumbleweeds from the MAN.... while he has posted on other topics...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-17-2017, 06:39 PM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    Thank you JB White and jrhead75 for answering the unasked questions from any new guys out there. Sometimes I get tunnel visioned on the issue and...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-17-2017, 01:26 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    burkfj, I too hope for the sake of the volumes of new Enfield enthusiasts that seem to find the SF forums, that the poster will at least engage in...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-16-2017, 08:03 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    Found it.... it's called "The Company BSA" which stands for British Sword Academy... here is the logo below.... Looked at his facebook page, (open...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-16-2017, 06:14 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    Last I heard the turki had discovered that not only did seven of his nine grandfathers singlehandedly win pivotal battles in both world wars, but one...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-16-2017, 05:51 AM
    Son replied to a thread A good laugh in The Lee-Enfield Forum
    This exact argument was IIRC one of the last I had over there.... I went to the trouble of doing intricate pictures with measurements and...
    36 replies | 1131 view(s)
  • Son's Avatar
    03-15-2017, 06:38 AM
    Son replied to a thread problem in The Lee-Enfield Forum
    After a bit of searching I have found the post on milsurps where Peter Laidler outlines a test for the bolt to receiver fit. Here is the relevant...
    12 replies | 1931 view(s)
  • Son's Avatar
    03-15-2017, 05:23 AM
    Son replied to a thread problem in The Lee-Enfield Forum
    Have seen it caused by several specific problems, or combinations of two or more of them causing it.... 1) Worn bolt head- usually very loose in...
    12 replies | 1931 view(s)
  • Son's Avatar
    03-15-2017, 05:08 AM
    Have seen it here too... IIRC it was called vendor bid, they could place one bid only at a time where bidding stalls.... not sure if it was only up...
    12 replies | 463 view(s)
  • Son's Avatar
    02-22-2017, 01:52 AM
    In your situation I would be looking for a bolt head in the high.630's range. If you end up a little too tight, then it can accelerate wear on the...
    16 replies | 662 view(s)
No More Results

4 Visitor Messages

  1. then maybe he shouldn't have taken me for an idiot
  2. View Conversation
    That guy has forgotten more about bayonets than many ever know. He deals internationaly
  3. View Conversation
    G'day Brad,

    How are things? Mate that scope I posted pics of the other day is going to be advertised very shortly, so I thought I'd let you know incase you or anyone you may know might be interested. It's not mine and it has no connection to me but I've been trying to buy a few enfield bits off this bloke and we discovered it. I'd like to see it go to the right individual. Not sure of the price. I've told him because it's missing some parts it may be worth a few hundred bucks, but he's been ringing around so I'm not sure. Anyway I can give you his details if you want them, just let me know.

    Demo
  4. View Conversation
    hi brad
    have you received my e:mail ??? thanks gary
Showing Visitor Messages 1 to 4 of 4
About Son

Basic Information

About Son
Occupation:
Fitter Armament

Signature


.....if it looks like a duck, walks like a duck and talks like a duck, but enough people call it a chicken, then it will be a chicken!

think about it...

Statistics


Total Posts
Total Posts
2,493
Posts Per Day
0.14
Last Post
Safety issues 03-21-2017 04:30 AM
Visitor Messages
Total Messages
4
Most Recent Message
01-19-2012 02:12 PM
General Information
Last Activity
Yesterday 05:15 AM
Join Date
12-31-1969
Referrals
1

1 Friend

  1. Markymark Markymark is offline

    Senior Member

    Markymark
Showing Friends 1 to 1 of 1